Home | BimmerBoard on AMAZON | Navigation A/V Forum | Post New Message | Search | Contact Moderator | Sign In  












Click to make a donation to support BimmerBoard
Follow BimmerBoard
Click to follow us on Twitter Click to follow us on FaceBook Click to follow us on MySpace
Related Links
BMW CCA
Indy Mechanics
E38.org Wiki
David's BMW Bookstore
BimmerBoard on AMAZON
E38.org
Yahoo BMW Nav Group
Frappr Map
Specialty Forums
Deals & Offers
IBUS Forum
Garage Forum
Navigation A/V
Bluetooth
For Sale
Want To Buy
Off-Topic
Detailing
///M
Kill Stories
Group Buys
Vanos Forum
Meet & Greet
TEST FORUM

Forums for Current Model BMW's
1 Series E81
3 Series E90
5 Series E60
5 Series F10 NEW
6 Series E63/E64
7 Series E65/E66
7 Series F01/02 NEW
X3 E83
X5 E70
X6 E71
Z4 E85
MINI Cooper

Forums for Past Model BMW's
2002
3 Series E21
3 Series E30
3 Series E36
3 Series E46
5 Series E12
5 Series E28
5 Series E34
5 Series E39
6 Series E24
7 Series E23
7 Series E32
7 Series E38
8 Series E31
X5 E53
Z3
Z8 E52
CS E9
Senior Six E3

Model-specific Lounges
E32 Lounge
E38 Lounge

Regional Forums
Australia
Canada
United Kingdom
Netherlands

Forums for Local BMW Car Clubs
Dallas
Southern California
Minneapolis
Atlanta


Click here to advertise on BimmerBoard.com




Return to the forum index Navigation A/V Forum

VDORepair pixel repair specialists

Subject: RECODE THE CAR - read below
Author: kiwijochen : member since June, 2006 : 2163 posts
Posted on: 2008-08-23 18:23:39      
Bookmark and Share

Design of MOST network
The MOST network is a bus for transmitting picture and audio data. In the E65, only audio data and control commands are transmitted. Bus communication functions in one direction. The control units are connected in series in the bus. The bus has a ring structure. If the temperature exceeds 70 °C in a device in the network, the Control Display indicates that the corresponding functions are no longer available. The entire MOST bus is powered down if the temperature exceeds 85 °C. Only the Control Display recognises the current application and its parameters such as the volume setting for listening to the radio. The Audio System Controller stores information regarding which control units are installed. This list of equipment can be called up in the Service menu of the Control Display. The equipment cannot be called up if the ring is interrupted. The Audio System Controller manages the audio sources by making available internal channels for outputting and by outputting the individual channel after being prompted by the Control Display. If the optional extra TOP Hi-Fi is fitted, the audio low frequency is recalculated prior to output and the improved audio low frequency is output.

MOST bus
The MOST (Media Oriented Systems Transport) network uses a ring bus for data communication between the various control units. Signal transmission is by means of fibre-optic cable. Data transmission on the ring bus takes place in one direction only. On the MOST network, messages can only be transmitted provided the bus ring is complete and fully functional. If there is a ring fault in the MOST network, however, the diagnosis system can only communicate with the instrument cluster and the Control Display. This is possible because those two control units are directly connected to the K-CAN SYSTEM bus.

If, for example, the power supply or the diode of a control unit is defective, it is no longer possible to communicate with the control units on the MOST bus. Exceptions here are of course the instrument cluster and the Control Display.

Save MOST ring configuration
This function determines the current configuration of the MOST ring, compares it with the vehicle order, and then saves it in the Audio System Controller.

CAUTION!

This function may only be run with a closed and complete started ring.

To save the MOST configuration correctly, the OPPS/OPS must not be connected to the MOST direct access point. If this is the case, remove the OPPS/OPS from the MOST ring and close the MOST ring with the original MOST direct access point in the vehicle.

Performance in event of ring break
If the MOST functions cannot be executed, this may be because of the following reasons:

No function can be selected - Fibre-optic cable interrupted, Voltage supply of at least one control unit interrupted, Serious software conflict of at least one control unit

Chosen functions cannot be selected - Severe software conflict of the control unit associated with the function

No function, note on excessive temperature - At least one function has shut down due to excessive temperature


VDORepair pixel repair specialists

The Navigation A/V Forum | Message Thread:


This thread is closed to new posts.


Make a donation to support BimmerBoard


Home | Privacy Policy | Terms of Service | Glossary | Advertising

Questions, comments, problems, please email webmaster@bimmerboard.com

©Copyright 2003-2010 BimmerBoard, LLC, All Rights Reserved.
No content from this web site may be reproduced or copied in any
form without the express written consent of BimmerBoard, LLC.


The BMW name and logos are registered trademarks of BMW AG
and BMW of North America, LLC.